Search result
Speaker installation
Determine the speaker system depending on the number of speakers you are using and install each speaker and subwoofer in the room.
Speaker installation is explained using this example of a typical installation.
FL/FR |
Place the FRONT left and right speakers an equal distance from the main listening position. The distance between each speaker and your TV should also be the same. |
C |
Place the CENTER speaker in between the front speakers and above or below your TV. |
SL/SR |
Place the SURROUND left and right speakers an equal distance to the left and right sides of the main listening position. If you don’t have surround back speakers, move the surround speakers slightly behind your listening position. |
SBL/SBR |
Place the SURROUND BACK left and right speakers an equal distance from the main listening position and directly behind the main listening position. When using a single surround back speaker (SB), place it directly behind the listening position. |
FWL/FWR (Front wide speaker left/right): |
Place the FRONT WIDE left and right speakers outside of the front left and right speakers so that there is an equal distance between all front speakers. |
SW 1/2 |
Place the SUBWOOFER at a convenient location near the front speakers. If you have two subwoofers, place them asymmetrically across the front of your room. |
FHL/FHR |
Place the FRONT HEIGHT left and right speakers directly above the front speakers. Mount them as close to the ceiling as possible and aim them towards the main listening position. |
TFL/TFR |
Mount the TOP FRONT left and right speakers on the ceiling slightly in front of your main listening position and aligned with the left and right front speakers. |
TML/TMR |
Mount the TOP MIDDLE left and right speakers directly above the main listening position and aligned with the left and right front speakers. |
TRL/TRR |
Mount the TOP REAR left and right speakers on the ceiling slightly behind your main listening position and aligned with the left and right front speakers. |
RHL/RHR |
Place the REAR HEIGHT left and right speakers directly behind the main listening position. Mount them as close to the ceiling as possible and aligned with the left and right front speakers. |
Upgrade (Auro-3D)
SHL/SHR |
Place the SURROUND HEIGHT left and right speakers directly above the surround speakers. |
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in place of Surround Height speakers.
FDL/FDR |
Place the FRONT Dolby Atmos Enabled speaker on the front speaker. For a Dolby Atmos Enabled integrated with a front speaker, place the Dolby Atmos Enabled speaker instead of the front speaker. |
SDL/SDR |
Place the SURROUND Dolby Atmos Enabled speaker on the surround speaker. For a Dolby Atmos Enabled speaker integrated with a surround speaker, place the Dolby Atmos Enabled speaker instead of the surround speaker. |
BDL/BDR |
Place the BACK Dolby Atmos Enabled speaker on the surround back speaker. For a Dolby Atmos Enabled speaker integrated with a surround back speaker, place the Dolby Atmos Enabled speaker instead of the surround back speaker. |
About Dolby Atmos Enabled speakers
Dolby Atmos Enabled speakers reflect the sound off the ceiling to allow the sound to come from over your head by using a special upward-pointing speaker that is placed on the floor.
You can enjoy the Dolby Atmos 3D sound even in an environment where speakers cannot be installed on the ceiling.
This unit is compatible with Audyssey DSX®, Dolby Atmos and DTS:X which offers an even wider and deeper surround sensation.
When using Audyssey DSX®, install front wide speakers or front height speakers.
Use the illustration below as a guide for how high each speaker should be installed. The height does not need to be exactly the same.
Upgrade (Auro-3D)
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in place of Surround Height speakers.
When 7.1-channel speakers are installed using surround back speakers
∗1:22° - 30° ∗2:90° - 110° ∗3:135° - 150°
When using a single surround back speaker, place it directly behind the listening position.
When 9.1-channel speakers are installed using front wide speakers
∗1: 22° - 30° ∗2: 55° - 60° ∗3: 90° - 110° ∗4: 135° - 150°
When 5.1-channel speakers are installed
∗1:22° - 30° ∗2:120°
Layout including height speakers and ceiling speakers
Height speaker layout example
Combination of 5.1-channel layout and front height/rear height speakers.
Ceiling speaker layout example
Combination of 5.1-channel layout and top front/top rear speakers.
Dolby Atmos Enabled speaker layout example
Combination of 5.1-channel layout and front Dolby/surround Dolby speakers.
Upgrade (Auro-3D)
Auro-3D layout example
Combination of 5.1-channel speakers with Front Height/Surround Height speakers.
For the best Auro-3D experience Surround Height speakers are recommended, however you may substitute Rear Height speakers from a Dolby Atmos speaker setup in place of Surround Height speakers.