Operating macro function

When the macro function is used, operations that usually require a complicated series of multiple button operations can be performed easily just by pressing the MACRO button.

This unit can remember up to 4 macro functions.

Each macro can record a maximum of 18 steps.

Bracket Open Example Bracket Close

When the following set of operations has been registered to the MACRO button, you can simply press the MACRO button to turn on the TV and this unit and start playing back Blu-ray Disc player.

Turn the TV’s power on.

Down Arrow

Turn this unit’s power on.

Down Arrow

Switch this unit’s input source to “Blu-ray”.

Down Arrow

Turn the Blu-ray Disc player’s power on.

Down Arrow

Play the Blu-ray Disc player.

Recording automatic macro operations

You can automatically set the macro for your scene.

Watch movies (MOVIE)
Listen to music (MUSIC)
Watch TV (CBL/SAT) (WATCH)
Turn on all devices (ON)
Turn off all devices (OFF)
NOTE

Register preset codes for the remote control unit before setting Auto macro. link

Depending on the type or model of your device, macro may not work properly even if it is set.

Press and hold RC SETUP for more than 3 seconds.

“SETUP” and LED_RC indicator flashes twice on the remote control unit.

Use shirosankaku shirosankaku-Reverse to display “MACRO” on the remote control unit and press ENTER.
Use shirosankaku shirosankaku-Reverse to display “AUTO” on the remote control unit and press ENTER.
When “MCNo” appears on the remote control unit, press the MACRO A – D button that you want to set.
Use shirosankaku shirosankaku-Reverse to set the auto macro operation and press ENTER.

“OK” flashes four times on the remote control unit and the normal operation mode is restored.

Remote control unit display

Auto MACRO

MOVIE

Automatically turns on the devices and starts playback when you watch movies.

 

TV power ON
Blu-ray power ON
AVR Power ON
Source Change “Blu-ray”
Playback Blu-ray Disc

MUSIC

Automatically turns on the devices and starts playback when you listen to music.

 

CD power ON
AVR Power ON
Source Change “CD”
Playback CD

WATCH

Automatically turns on the devices and starts playback when you watch TV (CBL/SAT).

 

TV power ON
CBL/SAT Power ON
AVR Power ON
Source Change “CBL/SAT”

ON

Turns on all the devices set for PRESET.

 

All device power on

OFF

Turns off all the devices set for PRESET.

 

All device power off

Recording custom macro operations

Press and hold RC SETUP for more than 3 seconds.

“SETUP” and LED_RC indicator flashes twice on the remote control unit.

Use shirosankaku shirosankaku-Reverse to display “MACRO” on the remote control unit and press ENTER.
Use shirosankaku shirosankaku-Reverse to display “MAN” on the remote control unit and press ENTER.
When “MCNo” appears on the remote control unit, press the MACRO A – D button that you want to set.
Press the buttons to be stored one by one.

The step number for the storing procedure and mode are alternately displayed on the remote control unit.

NOTE

You cannot store the macros for the ZONE SELECT button.

Press RC SETUP to exit the macro function.

“OK” flashes four times on the remote control unit and the normal operation mode is restored.

Adjusting the interval time of macro operations transmitting

The macro operation transmission interval can be adjusted.

The default setting is “0.50”.

Press and hold RC SETUP for more than 3 seconds.

“SETUP” and LED_RC indicator flashes twice on the remote control unit.

Use shirosankaku shirosankaku-Reverse to display “MACRO” on the remote control unit and press ENTER.
Use shirosankaku shirosankaku-Reverse to display “MAN” on the remote control unit and press ENTER.
When “MCNo” appears on the remote control unit, press the MACRO A – D button that you want to set.
Press RC SETUP.
Use shirosankaku shirosankaku-Reverse to set the macro operation transmission interval and press ENTER.

“OK” flashes four times on the remote control unit and the normal operation mode is restored.

Remote control unit display

Time values that you can set

0.25

0.25 sec

0.50

0.5 sec

0.75

0.75 sec

1.00

1 sec

1.25

1.25 sec

Using the macro function

Press the MACRO A – D button you used to store the macro function.

Resetting the macro function

Press and hold RC SETUP for more than 3 seconds.

“SETUP” and LED_RC indicator flashes twice on the remote control unit.

Use shirosankaku shirosankaku-Reverse to display “RESET” on the remote control unit and press ENTER.
Use shirosankaku shirosankaku-Reverse to display “MACRO” on the remote control unit and press ENTER.
When “MCNo” appears on the remote control unit, press the MACRO A – D button that you want to reset.

“RESET” flashes four times on the remote control unit and the normal operation mode is restored.

back to top